DaveE
@davee
Member
Joined: 2021-05-23 11:17 am
Last seen: 2024-05-20 2:21 am
Topics: 6 / Replies: 1717
Reply
RE: Merge Two Arduino IDE Sketches - Crazy_Blink - Part 1

Hi Bill @billinfl, First, well done for struggling through my 'box set' sized post! I have been playing with software for around half a centur...

3 hours ago
Reply
RE: Arduino Stepper Control

Hi Ron @zander, @will and @azslab, Just some comments that I hope may be useful for turning Bill (@dronebot-workshop)'s demonstration sketch, into ...

4 hours ago
Reply
RE: RYLR896 Lora Module setup

Hi Ron @zander, Agree again!! I have a feeling (not checked, so may be mistaken), that I read that config changes are not saved through power cy...

5 days ago
Forum
Reply
RE: RYLR896 Lora Module setup

Hi Ron @zander, RE I think I need to take a closer look and do a comparison of the two API's. If the Lora module itself is the same, then add...

5 days ago
Forum
Reply
RE: RYLR896 Lora Module setup

Hi Ron @zander, I hope we are agreeing! Adafruit board ... I haven't compared carefully, but obvious advantages for recommending it appear to be:...

5 days ago
Forum
Reply
RE: More Questions on 74HC165 and 74HC595 Shift registers (2)

Hi @mikeburton_2000, Sorry about not replying earlier, but I have only just got a little more organised to try to look at this. But before I spend...

5 days ago
Reply
RE: RYLR896 Lora Module setup

Hi Ron @zander & Gary @gtmize, I Googled the board manufacturer name for the AT command sheet, plus a limited data sheet. I think Ron, y...

5 days ago
Forum
Reply
RE: RYLR896 Lora Module setup

Hi Ron @zander & Gary @gtmize, The AT command set document is at LoRa AT Command RYLR40x_RYLR89x_EN.pdf (reyax.com) I'll leave deciding whet...

5 days ago
Forum
Reply
RE: RYLR896 Lora Module setup

Hi Ron @zander, I did see the diagrams you posted ... in fact I had previously seen the same ones on Amazon and my replies were partly based on it...

5 days ago
Forum
Reply
RE: RYLR896 Lora Module setup

Hi Ron @zander and @gtmize, Ron: Sorry, it's too late for my grey cell tonight, so this might be rubbish, but isn't your script talking to the Ard...

5 days ago
Forum
Reply
RE: RYLR896 Lora Module setup

Hi Gary @gtmize, Sorry, I can only offer hints. I assume you are using 3.3V microcontroller, like an ESP32, Pico or one of the newer Arduinos? I...

5 days ago
Forum
Reply
RE: RYLR896 Lora Module setup

Hi @gtmize, Sorry, I haven't any experience of these modules, so just a few preliminary comments. From the limited data on the web, the REYAX...

6 days ago
Forum
Reply
RE: Merge Two Arduino IDE Sketches - Crazy_Blink - Part 1

Hi @lee-g, @zander, @billinfl, @byron, In reply to an "overwhelming" number of requests, I attach a pdf of this previously posted topic. Or to be ...

1 week ago
Reply
RE: Merge Two Arduino IDE Sketches - Crazy_Blink - Part 1

Hi @lee-g, I'll try to put a pdf up sometime tomorrow (UK time) ... hopefully I have it, but it was a 'handraulic' transfer, possibly with tweaks...

1 week ago
Reply
RE: Merge Two Arduino IDE Sketches - Crazy_Blink - Part 1

Hi @byron, Thanks for your constructive thoughts, which are very much appreciated. In terms of the technical points to include, I wasn't sure ...

1 week ago
Page 1 / 115