Notifications
Clear all

Enclosures, where, anyone?

9 Posts
3 Users
1 Reactions
1,346 Views
(@tom-b)
Member
Joined: 1 year ago
Posts: 7
Topic starter  

Hey, gang.  I have been looking for an enclosure for a power supply.  I need one about 9x12, or 10x12, but simply cannot find anything like this.  Have tried Amazon, Ebay, Jameco, Digikey, and various manufacturers.  Anyone have any help on where to go?

Many thanks, Tom



   
Quote
(@dronebot-workshop)
Workshop Guru Admin
Joined: 7 years ago
Posts: 1189
 

Hi Tom

I usually buy mine on Amazon; I spotted this one that looks like it may work as a power supply (and I have purchased a similar one from them before, which was pretty good). However, you mentioned that you had already looked there and didn't find anything suitable.

Are there any additional requirements for your case that we should know?

😎

Bill


This post was modified 1 year ago by DroneBot Workshop

"Never trust a computer you can’t throw out a window." — Steve Wozniak


   
ReplyQuote
fransK
(@fransk)
Member
Joined: 1 year ago
Posts: 21
 

Hi Tom,

If you have some time to spare and make your hands dirty: have you thought about using aluminium t-slot profiles to make your own case, https://www.google.com/search?q=alu+t-slot+profile


Pingpong is fun


   
ReplyQuote
(@tom-b)
Member
Joined: 1 year ago
Posts: 7
Topic starter  

Thanks, frasK.  I had not thought about it.  I had always imagined such material for larger frameworks for precision tools!  I will have to investigate, and find a source for sheet aluminum for the walls, etc.

Best regards, Tom



   
ReplyQuote
(@tom-b)
Member
Joined: 1 year ago
Posts: 7
Topic starter  

Posted by: @tom-b
↑

simply

 



   
ReplyQuote
(@tom-b)
Member
Joined: 1 year ago
Posts: 7
Topic starter  

Dear Bill,

Thanks so much for taking time out of your schedule to help me with the enclosure issue.  I think I recognize this one as shown on your excellent video on llinear power supplies.  This will likely solve the issue!

Many thanks, Tom



   
ReplyQuote
(@tom-b)
Member
Joined: 1 year ago
Posts: 7
Topic starter  

@dronebot-workshop 

Hi, Bil.  Thanks again for the recommended enclosure from Amazon.  I wonder if you have any thoughts about a plastic chasis (this one is plastic) for a power supply.  I am used to thinking of them as grounded metal, but maybe it does not make any difference.  I would be greatful for your thoughts.  Tom



   
ReplyQuote
(@dronebot-workshop)
Workshop Guru Admin
Joined: 7 years ago
Posts: 1189
 

Are we talking about a linear or switching power supply, Tom?  Linear power supplies tend to dissipate more heat, thus the requirement for a heatsink on the voltage regulator.  That might be a problem for some plastic cases, although at low current with some adequate ventation holes, this could work.

Switching supplies run a lot cooler and are often built in plastic cases; most notebook computer power supplies use plastic cases.

Metal is superior for both applications, at least in my opinion it is. It can dissipate heat on a linear supply and can also help shield the electrical noise that some switching supplies produce.

Another option, if you can find it, is cases built with "impregnated plastic", meaning that the plastic has other materials blended into it. Some are made with metal powder, allowing them to be used for grounding or shielding. 

And on the subject of shielding and grounding, most metal chassis are built with aluminum, which is not an effective shield (or electrical conductor). Steel ones are superior, but they add to the weight and cost.

😎

Bill


"Never trust a computer you can’t throw out a window." — Steve Wozniak


   
ReplyQuote
(@tom-b)
Member
Joined: 1 year ago
Posts: 7
Topic starter  

@dronebot-workshop

Thank you , Bill.  Very informative.  I am trying to design, and have a schematic, to build a linear power supply with two sides.  One side is with dual rails for use by Op Amps.  The other side is similar to the linear supply you built in your video about linear supplies some years ago, with three fixed voltages, or perhaps four.  Meters on both sides will serve to warn users not to exceed 4.5 Amps total when using one or the other sides.  Sounds a little complex, I know. The reason it is linear is I want to have very little noise on the rails for Op Amp work, and consequently this allows little noise in the lower voltages for logic, etc., work.   

I have considered building just one dual rail linear supply for Op Amps, splitting the transformer voltage as you reminded us in your video on Op Amps.  I think I have developed a way to reinforce the bottom of a plastic case to hold the weight of the transformer. I have located a transformer suited to this type of project.  The LM350 voltage regulator at 3 amps should also assist, or perhaps the LD1085.

For the heat issue, I have all along known that I will have several heat-making and heat-sensitive parts in such a machine.  Consequently, I have planned forced air ventilation together with adequate heat sinks.  I hope this will do, but I will check out the math for the heat sinks first.

I think that covers some of the details I have left out in previous posts.  I will continue to look for a steel or impregnated plastic (or failing that, use plastic or aluminum) enclosure that will fit the transformer and circuit board. Your previous suggestion would work fine!

I have experience in doing electronics and tech, mostly with microcomputers.  I find your site very engaging, and the use of modern microcontrollers is right up the alley of building data recorders that I worked on most of my time in this business.  You mention a site by an 'Andreas' that you compliment.  Could you give me his Youtube name or .com site name so I might explore, please?  Best regards, Tom.



   
ReplyQuote