Notifications
Clear all

Arduino Nano..cant upload to it..  

  RSS

Graham410
(@graham410)
Active Member
Joined: 9 months ago
Posts: 10
2020-04-29 4:35 pm  

Hello guys, I am trying to use the arduino nano, but have failed to upload the blink sketch to it.

used Unos without any problems, but get the following error message. I will copy and paste page 8 of 8 it seems to tell what the problem is, but the previous 7 pages would flood the page with too much info so I think I had better not paste it in here unless requested.

sorry to troiuble you all guys I am sure you can help me please..

System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

 

Using Port : COM4

Using Programmer : arduino

Overriding Baud Rate : 115200

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x2a

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x2a

 

avrdude done. Thank you.

 

Problem uploading to board. See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

Invalid library found in C:\Users\Graham\Documents\Arduino\libraries\DHT-sensor-library-master: no headers files (.h) found in C:\Users\Graham\Documents\Arduino\libraries\DHT-sensor-library-master

Invalid library found in C:\Users\Graham\Documents\Arduino\libraries\DHT-sensor-library-master: no headers files (.h) found in C:\Users\Graham\Documents\Arduino\libraries\DHT-sensor-library-master


Quote
triform
(@triform)
Reputable Member
Joined: 1 year ago
Posts: 331
2020-04-29 5:12 pm  

Hi @graham410,

There are a few things you can check - Make sure you have the correct chip selected on the options menu for the board.  With the ones from China, they can have a 168 and others the 328.  Also, check the selection for the 328 with the old boot loader (Most of the ones from China have this) and the new boot loader (the other 328 selection)

 

Hope this helps.


ReplyQuote
starnovice
(@starnovice)
Estimable Member
Joined: 1 year ago
Posts: 169
2020-04-29 5:20 pm  

Probably already done this but open device manager and besure your system recognized the board and double check the COM port.  I have had problems with that with China stuff. In one case I could not hook up two nanos to my laptop because they both insisted on using the same COM port.

Pat Wicker (Portland, OR, USA)


ReplyQuote
Graham410
(@graham410)
Active Member
Joined: 9 months ago
Posts: 10
2020-04-29 6:58 pm  

@triform, hello there Triform, iI am very grateful to you.

it was exactly as you described it...

of the choices available there was a checkmark against Atmega 328p

so I tried the 168 choice, and that didnt work, but then I checked the Atmega328p(old bootloader) and it worked, many many thanks for your help.

 

 


ReplyQuote
Graham410
(@graham410)
Active Member
Joined: 9 months ago
Posts: 10
2020-04-29 8:58 pm  

@starnovice thank you Pat the previous poster has already solved it for me, many thanks for your kind help.

 

should i mark this post as closed now in some way please?


ReplyQuote
Graham410
(@graham410)
Active Member
Joined: 9 months ago
Posts: 10
2020-04-30 12:26 am  

thank you for your help guys all solved now....so grateful


ReplyQuote