I am new in this business. Tried many times to get the ESP32-cam to work. Used programs from 3 AI sources and Bill's Youtube vid from 2021. In vain. Never got it to compile properly.
Need simple program to take photos, should be compilable and working. Installed latest esp Software on Arduino.
@schober Just use the board sample called CameraWebServer. I use it often.
Did you get the MB boards? They are so much easier to work with. Here is a link to Amazon.CA, change country as needed search Amazon for [esp32-cam-mb] and pick one. The better models don't require you to hold the BOOT button during upload but I think I saw one model that had it all wrong, they referenced the wrong button and I am sure it didn't need any button. Any will work, some are just more convenient.
If you use that board, change the sample as follows and of course enter WiFi creds. If you want I can show you how to convert to WiFiManager.
First computer 1959. Retired from my own computer company 2004.
Hardware - Expert in 1401, 360, fairly knowledge in PC plus numerous MPU's & MCU's
Major Languages - Machine language, 360 Macro Assembler, Intel Assembler, PL/I and PL1, Pascal, Basic, C plus numerous job control and scripting languages.
My personal scorecard is now 1 PC hardware fix (circa 1982), 1 open source fix (at age 82), and 2 zero day bugs in a major OS.
Thanks! I made headway yesterday. Used the program from Arduino. Comp. Ok, uploading too. See the window with the parameters left side. But no photos when the button at the bottom is pressed.
Question there are two buttons on my device: I00, and RST . WHEN should I press them?
I have no idea what module to select. Tentatively I used Wrover. I also selected Huge App 3 MB
Should I buy a new one from Amazon? But which one? Thanks for your help, greetings from ol' Germany Tilman
@schober Last question first, but ANY board labelled esp32-cam MB see pic. Reset button causes your skecth to run from setup. The other button has different names but it's use is during upload but only with certain USB-UART chips (I don't recall which but it will be obvious) When you see Connecting.. press and hold the BOOT button for a bit, if unsure hold it until upload is 100%. I am enclosing a pic of a typical AI-THINKER style board but it actually carries someone else's name (if you understand how the Chinese factories work you will understand how this happens, it is NOT like a lot of people think) I am also enclosing a board I just noticed in my Amazon search. It has many advantages BUT I have no idea if it will work with the sample sketch.
I have bought over a dozen of these boards and the MB daughter boards on Aliexpress for a fraction of the cost of Amazon if you care.
Here is the link to the first board pictured https://amz.cx/3J6F
and this is the link to the 2nd board that I don't have but looks very interesting. https://amz.cx/3J6H
these are Amazon.ca links, adjust for your country.
p.s. When replying, please use the Reply link at the bottom of the post you are replying to, that way they get an email to tell them a reply has been posted to their post.
First computer 1959. Retired from my own computer company 2004.
Hardware - Expert in 1401, 360, fairly knowledge in PC plus numerous MPU's & MCU's
Major Languages - Machine language, 360 Macro Assembler, Intel Assembler, PL/I and PL1, Pascal, Basic, C plus numerous job control and scripting languages.
My personal scorecard is now 1 PC hardware fix (circa 1982), 1 open source fix (at age 82), and 2 zero day bugs in a major OS.
@zander hi, thanks for the prompt answer ! What is your first name? Mine is Til. I ordered now a new esp32-cam from Amazon. I played with my device today, but to no avail.- Are you Canadian citizen? Best regards, Til
@schober Hi Til, I am Ron but as you saw my handle is zander (old nickname from high school) Which device did you order, maybe the best way is to post a link, but if it's on Amazon do NOT post a regular link, there is a bug in the forum software that messes with the link. Either use a URL shorter or enclose the link in " ".
Show me a picture of your esp32cam.
Send me the link to the sketch you are trying to use.
Yes Canadian Citizen, my family roots go back 7 generations, we have roads named after us.
BTW, I am unable to get my esp32cam to work now, some sort of Mac bug I think but I will persevere.
First computer 1959. Retired from my own computer company 2004.
Hardware - Expert in 1401, 360, fairly knowledge in PC plus numerous MPU's & MCU's
Major Languages - Machine language, 360 Macro Assembler, Intel Assembler, PL/I and PL1, Pascal, Basic, C plus numerous job control and scripting languages.
My personal scorecard is now 1 PC hardware fix (circa 1982), 1 open source fix (at age 82), and 2 zero day bugs in a major OS.
ust use the board sample called CameraWebServer. I use it often.
I'm going to lurk on this thread because I also had difficulty getting the camera sketches to work but don't have time to focus on it. IIRC, the sketch complained about memory not found. I tried every model without success. I finally just pushed the issue into the "later" pile.
The one who has the most fun, wins!
have been in Canada quite often. Been to Chalk River Lab., Ont. for 2 months, been to Whitehorse on my way to Alaska, drove from Calgary, Alberta to Vancouver with a camper , have seen Banff and Lake Louise. Been several times to Toronto and Quebec, and so on...
@tfmccarthy That error is probably caused by a mismatch between the board and the #defines. You need to enable ONLY one define that matches your board. The current sample is for ESP_EYE but most of us own the AI_THINKER.
First computer 1959. Retired from my own computer company 2004.
Hardware - Expert in 1401, 360, fairly knowledge in PC plus numerous MPU's & MCU's
Major Languages - Machine language, 360 Macro Assembler, Intel Assembler, PL/I and PL1, Pascal, Basic, C plus numerous job control and scripting languages.
My personal scorecard is now 1 PC hardware fix (circa 1982), 1 open source fix (at age 82), and 2 zero day bugs in a major OS.
@schober You have seen some nice places here then. If you haven't already, the drive from Calgary to Jasper is probably the #1 scenic drive in the country, #2 and #3 are down East and #4 is the North Shore (Sudbury to Thunder Bay) where I live.
Is it Chalk River where former President Jimmy Carter risked his life in a nuclear accident?
As far as scenery, I also love the NE of the USA, used to own a ski condo timeshare in North Conway NH. We also love the mountains of the US west coat and of course UTAH. We both live in beautiful countries, I wonder though for how long.
First computer 1959. Retired from my own computer company 2004.
Hardware - Expert in 1401, 360, fairly knowledge in PC plus numerous MPU's & MCU's
Major Languages - Machine language, 360 Macro Assembler, Intel Assembler, PL/I and PL1, Pascal, Basic, C plus numerous job control and scripting languages.
My personal scorecard is now 1 PC hardware fix (circa 1982), 1 open source fix (at age 82), and 2 zero day bugs in a major OS.
I don't know anything about that Carter incident.- I once attended a Tritium Workshop in Toronto. Canada produces a lot of tritium in the Candu reactors. I used to be one of the main tritium experts in Germany.
Take care, Tilman, or Til
@schober It was in 1952 and was the first nuclear accident in North America. Carter led a team and each man had 90 secs. They were lowered into the reactor wrench in hand and ran to the reactor to turn one screw then back out. He was told he would never have any kids, but he had 4 and lived to 100. Some kind of superman?
First computer 1959. Retired from my own computer company 2004.
Hardware - Expert in 1401, 360, fairly knowledge in PC plus numerous MPU's & MCU's
Major Languages - Machine language, 360 Macro Assembler, Intel Assembler, PL/I and PL1, Pascal, Basic, C plus numerous job control and scripting languages.
My personal scorecard is now 1 PC hardware fix (circa 1982), 1 open source fix (at age 82), and 2 zero day bugs in a major OS.
@schober Show me a photo of the camera you are using. The photos and videos are probably on your PC somewhere, try the Recents tab in File Explorer, or check Downloads (with sequence set to last modified and most recent at top (descending?)) of Photos or Documents.
First computer 1959. Retired from my own computer company 2004.
Hardware - Expert in 1401, 360, fairly knowledge in PC plus numerous MPU's & MCU's
Major Languages - Machine language, 360 Macro Assembler, Intel Assembler, PL/I and PL1, Pascal, Basic, C plus numerous job control and scripting languages.
My personal scorecard is now 1 PC hardware fix (circa 1982), 1 open source fix (at age 82), and 2 zero day bugs in a major OS.
@schober Post the link (use a shortener or in " ") of the camera you purchased on Amazon.
First computer 1959. Retired from my own computer company 2004.
Hardware - Expert in 1401, 360, fairly knowledge in PC plus numerous MPU's & MCU's
Major Languages - Machine language, 360 Macro Assembler, Intel Assembler, PL/I and PL1, Pascal, Basic, C plus numerous job control and scripting languages.
My personal scorecard is now 1 PC hardware fix (circa 1982), 1 open source fix (at age 82), and 2 zero day bugs in a major OS.




