<?xml version="1.0" encoding="UTF-8"?>        <rss version="2.0"
             xmlns:atom="http://www.w3.org/2005/Atom"
             xmlns:dc="http://purl.org/dc/elements/1.1/"
             xmlns:sy="http://purl.org/rss/1.0/modules/syndication/"
             xmlns:admin="http://webns.net/mvcb/"
             xmlns:rdf="http://www.w3.org/1999/02/22-rdf-syntax-ns#"
             xmlns:content="http://purl.org/rss/1.0/modules/content/">
        <channel>
            <title>
									Wire Claw - Arduino				            </title>
            <link>https://forum.dronebotworkshop.com/arduino/wire-claw/</link>
            <description>Discussion board for Robotics, Arduino, Raspberry Pi and other DIY electronics and modules. Join us today!</description>
            <language>en-US</language>
            <lastBuildDate>Tue, 17 Nov 2026 02:29:28 +0000</lastBuildDate>
            <generator>wpForo</generator>
            <ttl>60</ttl>
							                    <item>
                        <title>RE: Wire Claw</title>
                        <link>https://forum.dronebotworkshop.com/arduino/wire-claw/#post-52825</link>
                        <pubDate>Wed, 17 Jun 2026 09:22:33 +0000</pubDate>
                        <description><![CDATA[Hi,
Since the ESP32-C6 is already online and you can read the chip temperature under Devices, the sensor/device side is probably working fine. The error looks more related to the LLM/API ca...]]></description>
                        <content:encoded><![CDATA[<p>Hi,</p>
<p>Since the ESP32-C6 is already online and you can read the chip temperature under Devices, the sensor/device side is probably working fine. The error looks more related to the LLM/API call rather than the ESP32 itself.</p>
<p>A few things I would check:</p>
<ol>
<li>
<p>Make sure the API key is valid and has enough quota/credits.</p>
</li>
<li>
<p>Confirm that the selected LLM model name matches what the firmware expects.</p>
</li>
<li>
<p>Check whether the firmware is using OpenAI, Gemini, or another provider, and verify the correct endpoint/API format.</p>
</li>
<li>
<p>Try a very simple command first, such as “hello” or “what devices are available?”</p>
</li>
<li>
<p>If serial logs are available, monitor the ESP32-C6 output while sending the Telegram command. It may show whether the failure is authentication, timeout, model not found, or invalid request.</p>
</li>
</ol>
<p>Since Telegram is responding but the message says “LLM call failed,” I would mainly suspect the API key/model/provider configuration or API quota rather than WireClaw device detection.</p>
<p>Best regards.</p>]]></content:encoded>
						                            <category domain="https://forum.dronebotworkshop.com/arduino/">Arduino</category>                        <dc:creator>aliarifat</dc:creator>
                        <guid isPermaLink="true">https://forum.dronebotworkshop.com/arduino/wire-claw/#post-52825</guid>
                    </item>
				                    <item>
                        <title>Wire Claw</title>
                        <link>https://forum.dronebotworkshop.com/arduino/wire-claw/#post-52758</link>
                        <pubDate>Mon, 25 May 2026 15:02:28 +0000</pubDate>
                        <description><![CDATA[I am trying to run the published Wire Claw project on a ESP32-C6. 
After installing the WireClaw firmware successfully on the ESP32-C6 and configuring WireClaw I can now read chip temp unde...]]></description>
                        <content:encoded><![CDATA[<p>I am trying to run the published Wire Claw project on a ESP32-C6. </p>
<p>After installing the WireClaw firmware successfully on the ESP32-C6 and configuring WireClaw I can now read chip temp under Devices.</p>
<p>But after writing this command in Telegram; what is the chip temperature?  I keep on getting this Error.</p>
<p>      "error: LLM call failed]”</p>
<p>I have configured: Telegram Bot Token, Chat ID &amp; API Key correctly, according to the instructions.</p>
<p>I have spent several days with this problem and I find this to be a very useful and interesting project.</p>
<p>My question is;  Do you have any magic tips How to solve this error? </p>
<p>Greatful for any tips or hints.</p>
<p>Best regards,</p>
<p>@bomtech</p>]]></content:encoded>
						                            <category domain="https://forum.dronebotworkshop.com/arduino/">Arduino</category>                        <dc:creator>bomtech</dc:creator>
                        <guid isPermaLink="true">https://forum.dronebotworkshop.com/arduino/wire-claw/#post-52758</guid>
                    </item>
							        </channel>
        </rss>
		